|Place of Origin:||China|
|Minimum Order Quantity:||1 Set|
|Packaging Details:||Standard Export Wooden Case|
|Payment Terms:||T/T, Western Union|
|Supply Ability:||1000 Set Per Months|
|Name:||New Flat Vulcanizing Machine For Belt And Tire Small Vulcanizer Machine||Working Mode:||Electric Heating|
|Hot Plate:||350 × 350mm||Cylinder Stroke:||Max 300mm|
|Cylinder Speed:||11mm / S||Temperature Control Mode:||PLC Touch Screen|
Belt Flat Vulcanizing Machine,
Tire Flat Vulcanizing Machine,
Small Vulcanizer Machine
New Flat Vulcanizing Machine For Belt And Tire Small Vulcanizer Machine
1). First adjust the test machine horizontally, and use the level on the base of the machine, and adjust the basic screw according to the level indicator to make it level (adjust when installing the machine or moving the machine).
2). Start the main power switch and let the power supply pass through the control panels of the machine.
3). Set the test temperature.
4). Set the temperature of the upper, middle upper, middle lower and lower molds according to the requirements of the materials. After the temperature reaches the set temperature, open the cylinder door and place the stainless steel plate and the sample.
5). Start the test button to start the test on the hydraulic cylinder (do not adjust the pressure and speed of the hydraulic system).
6). The system automatically resets after the set time is reached.
7). Observe the sample and the test is over.
Precautions and maintenance
1).The display of this unit, the power of the motor is input according to the label.
2).The operator must be familiar with the operation and maintenance methods of this unit and pay attention to its use.
3).The environment should be kept clean and not wet.
4).When necessary, please pay attention to handling, do not damage the machine.
5).When replacing the jig, pay attention to pick and place, so as not to fall and bump the machine.
6).Regularly check the drive belt to see if it is looseness or not and adjust it.
7).Please apply for inspection calibration regularly to ensure accuracy.
This series of flat vulcanizing machines are used in the main equipment for pressing and forming various rubber model products and non-model products. They can also be used to suppress all kinds of thermosetting plastics and foaming rubber and plastic products. With independent power mechanism and electrical system, centralized control with buttons. The working pressure and heating temperature can be adjusted within a certain range. This model is divided into manual and semi-automatic.
1).Capacity: 5-30ton (adjustable)
2).Temperature range: normal temperature ~ 250 ° C
3).Temperature accuracy: ± 0.5 ° C
4).Temperature controller: PLC touch screen
5).Temperature control mode: PLC touch screen
6).Heating: electric heating tube heating
7).Working mode: electric heating. Heating method: electric heating
8).Heating time: about 15min from room temperature to 160 °C (heating speed adjustable)
9).Timer: PLC display, 0.01S ~ 999min ~ 999hr (adjustable)
10).Hot plate: 350 × 350mm (specially treated high hardness steel plate) electric heating water cooling.
11).Exhaust function: low pressure automatic exhaust one minute 3 to 10 times adjustable
12).Hydraulic system: proportional hydraulic flow closed loop control system, GPY oil pump (made in Japan) drives high-performance electro-hydraulic with high-precision non-resistance cylinder piston to perform equal-rate control mode (stroke height can be set independently) with automatic pressure Compensation function, pressurization time can be preset, load force is strong, lifting is stable, automatic pressurization, pressure holding, pressure relief
13).Cylinder stroke: Max 300mm
14).Cylinder speed: 11mm / s
15).Pressure table: 0 ~ 200kg / sq.cm
16).Volume: (W × D × H) 1400 × 750 × 1460 mm
17).Power: 3 ∮, AC220V, 15A
18).Weight: about 350kg
Contact Person: Vicky He